| From | Message |
marty
Dodge Dakota
JOIN HERE
6/06/2006
18:02:20
|
 Subject: P 700 code
IP: Logged
Message:
I have a 2000 dodge dakota with a 4.7L and the check engine light came on I ran the code and it came up a P 700,not real sure what it means if anyone can help I would greatly appreciate it.
|
That guy
Dodge Dakota
JOIN HERE
6/06/2006
18:07:58
|  RE: P 700 code
IP: Logged
Message:
is the code p 0700? if so P0700 EATX Controller DTC Present This SBEC III or JTEC DTC indicates that the EATX or Aisin controller has an active fault and has illuminated the MIL via a CCD (EATX) or SCI (Aisin) message. The specific fault must be acquired from the EATX via CCD or from the Aisin via ISO-9141. What ever that means
|
marty
Dodge Dakota
JOIN HERE
6/06/2006
19:21:45
| RE: P 700 code
IP: Logged
Message:
From what you said I am going to have to take it to the dealer for more info?
|
RobC
Dodge Dakota
JOIN HERE
6/07/2006
01:29:30
|  RE: P 700 code
IP: Logged
Message:
Have you checked the trans fluid level? What was going on when the MIL lit up? Has the code cleared yet? Was/is it running normally or is it in "limp home" mode?
|
marty
Dodge Dakota
JOIN HERE
6/07/2006
07:44:34
| RE: P 700 code
IP: Logged
Message:
At the time the code came on I was pulling a utility trailer I used for work.It would statrt off fine but had no power as you would climb a hill and also no passing gear.
|
marty
Dodge Dakota
JOIN HERE
6/07/2006
07:47:10
| RE: P 700 code
IP: Logged
Message:
Also the code has not cleared since I parked it last night,Iwill see if it is better since I am not hauling the trailer today.
|
marty
Dodge Dakota
JOIN HERE
6/07/2006
14:55:06
| RE: P 700 code
IP: Logged
Message:
The truck acts like it has lost overdrive.
|
Rob C
Dodge Dakota
JOIN HERE
6/08/2006
00:59:59
| RE: P 700 code
IP: Logged
Message:
What about the fluid level? Have you tried to reset the PCM (of course, it looks like the error is stored in the TCM) by pulling one of your battery cables and turning the ignition key to 'start' for about 20 seconds? I think that P0700 code is a very general transmission code. You may have had too much transmission slippage while pulling the trailer. A lot of times these codes will come up and won't clear for 3 or 4 start cycles even if the fault condition doesn't exist anymore.
|
QQQ
Dodge Dakota
JOIN HERE
6/10/2006
14:03:12
| RE: P 700 code
IP: Logged
Message:
PO700 --- This code will set a DTC code (Diagnostic Trouble Code "DTC") Bring the truck to autozone or someplace and have them read the code with a code reader. This will give you the code of what went wrong. I had a po700 once, code said transmission output speed control sensor. Bought a new one (40$) put it in, problem fixed. As for losing overdrive, as soon aas the code set, the transmission went into "limp home mode" lost 1st gear, overdrive, and trans shifted HARD. This is normal, supposed to act like that. Get that code read, will probably tell you what's wrong.
|
marty
Dodge Dakota
JOIN HERE
6/10/2006
17:12:58
|  RE: P 700 code
IP: Logged
Message:
Thank you for all of your help found out that the speed sensor failed replaced them and it works great.
|
BansheeBoy
Dodge Dakota
JOIN HERE
9/16/2008
19:06:38
| RE: P 700 code
IP: Logged
Message:
I got the same code on a 1997 chevy Z71. the truck does exactly every thing all of you said. just now finding you guys info. gonna shoot down to auto store and see if they can halp with further analyzing. Thanks DODGE DUDES
|
jlindsey
Dodge Dakota
JOIN HERE
10/01/2008
16:30:51
| RE: P 700 code
IP: Logged
Message:
0441 code popped up on my 04 dakota cc 4.7 evap emmissions? thats what the scan tool said any ideas on what it is or could be??
|
Tony
Dodge Dakota
JOIN HERE
3/06/2009
15:32:35
| RE: P 700 code
IP: Logged
Message:
Where is that sensor located? I'm having the same problems with the transmission not shifting properly. I don't have 1st or overdrive.
|
simon
Dodge Dakota
JOIN HERE
3/16/2010
13:31:57
| RE: P 700 code
IP: Logged
Message:
check your lock-up on your torque converter this is use a an overdrive and you should not gon on overdrive wile your tracking heavy wheight. or maybe the proble is just your torque converter
|
psssst
Dodge Dakota
JOIN HERE
3/16/2010
18:33:29
| RE: P 700 code
IP: Logged
Message:
You're responding to a post that is 1 year and 10
days old (to be exact)
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
