| From | Message |
GSMarquis
Dodge Dakota
JOIN HERE
5/08/2002
20:45:56
|
 Subject: carsound highflow cat
IP: Logged
Message:
Does anyone know if the carsound highflow cat is a bolt on cat....i think its part number 94016...BTW i have a 2001 4.7
|
bernd
*GenIII*
5/08/2002
22:04:31
| RE: carsound highflow cat
IP: Logged
Message:
Nope...it needs to be welded on.
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
GSMarquis
Dodge Dakota
JOIN HERE
5/08/2002
22:19:32
| RE: carsound highflow cat
IP: Logged
Message:
ok so if i have no sensors after the cat then i can change it to a carsound cat......and what if i fail a inspection?
|
bernd
*GenIII*
5/09/2002
08:14:25
| RE: carsound highflow cat
IP: Logged
Message:
I wouldn't worry about it. If you do fail inspection ("sniffer" test), then i'd be worried about something else wrong with the engine. These trucks run very clean as is. The Carsound Cats are OBD-II compliant as well.
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
Rob
GenIII
5/09/2002
11:59:41
| RE: carsound highflow cat
IP: Logged
Message:
Bernd I need a cat to replace my third cat any suggestions?
|
bernd
*GenIII*
5/09/2002
12:34:33
| RE: carsound highflow cat
IP: Logged
Message:
I've had great success with Carsound.
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
R/Truck
Dodge Dakota
JOIN HERE
5/09/2002
13:35:22
| RE: carsound highflow cat
IP: Logged
Message:
I have the carsound cat and it performs so good you don't even think its there.
|
B1llyw
GenIII
5/10/2002
08:21:46
| RE: carsound highflow cat
IP: Logged
Message:
My 2002 truck has an 02 sensor after the 3rd cat. Lucky me. Can I use that 94016 part number on my truck? I'm assuming I would just have to weld in an 02 bung. Or is there a direct fit cat for my truck?
Bill White - 2002 QC 4x4, SLT , 4.7, 5 spd, 3.92's, Airaid, MBRP Super Single, Hurst T-Handle, BFG A/T's, IAS Shocks, 180 T-Stat, Jet Chip - Stage II
|
R/Truck
Dodge Dakota
JOIN HERE
5/10/2002
12:20:21
| RE: carsound highflow cat
IP: Logged
Message:
They just weld it in line with your existing pipe and this is also a great chance for you to increase the pipe from the y-pipe back to the muffler to 3". Then just weld a new o2 bung that.
|
spin
Dodge Dakota
JOIN HERE
7/20/2004
23:56:25
| RE: carsound highflow cat
IP: Logged
Message:
i dont have a o2 sensor after my 3rd cat, which cat would be good to just replace the pre cats?
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
