| From | Message |
Ryan
Dodge Dakota
JOIN HERE
9/12/2002
11:53:40
|
 Subject: IAT Adjuster
IP: Logged
Message:
Guys,
got a 4.7L v8 2000 dak
I have built the adjuster.. anyone else have one .. if so .. let me know how you installed it .. Wire colors .. in my truck black with white stripe and black with blue stripe..on the orginal sensor wire colors .
I just get the engine light comming on .. they have to reset the pcm to clear it .. . no error code ... when screwing with the "IAT adjuster"..
i have tryed almost everthing .. resodered all points again and asked a few guys at my work that are electrical eng. they say that it fine ..
|
DaveR
GenII
9/12/2002
18:10:17
|  RE: IAT Adjuster
IP: Logged
Message:
I've got the same problom at the moment. I am going to fiddle with it somemore and swap wires. Maybe someone will post an answer before I spend hours yelling at it.
|
Canucker
Dodge Dakota
JOIN HERE
9/12/2002
18:30:03
| RE: IAT Adjuster
IP: Logged
Message:
before you install the adjuster, I'd reccomend you take an ohm meter to your IAT sensor and see what the reading is (that's be the ambient air temp) ... mine was around 8-10 kohms? I think
then adjust your IAT box to be somewhere close to there to begin with .. that should give you a good starting point without any MILs coming on, then you can fine tune it from there.
|
DaveR
GenII
9/12/2002
21:22:03
| RE: IAT Adjuster
IP: Logged
Message:
You got any pics of the insides of yours? I don't think I have the curcuit right
|
foleyr
GenI
9/13/2002
09:45:29
| RE: IAT Adjuster
IP: Logged
Message:
ya dude will do .. just got to get a camera ..
someone took it right now .. i can draw a diagram if you want .. let me know ..
Ryan
foleyr ..
|
foleyr
GenI
9/13/2002
10:20:50
| RE: IAT Adjuster
IP: Logged
Message:
go here .. found a pict ..
www.geocities.com/hybrid54321
stupid debug errors .. just answer no ..
Then you should see pict ..
Ryan
foleyr ..
|
DaveR
GenII
9/13/2002
12:16:33
| RE: IAT Adjuster
IP: Logged
Message:
THat's the same pic as on the speedtweaks site. I think I got it all figured out using a multimeter. I turned the key to the on position to get a signal, then jst read which wires were doing what. Hope this helps anyone else that was having probloms.
|
foleyr
GenIII
9/13/2002
14:06:10
| RE: IAT Adjuster
IP: Logged
Message:
OK guys .
i had a few of the electric eng at my work place look at it .. i am going to try it at 4:00 pm est .. today .. 2 back wares to pcm and 2 white wires to sensor .. should work .. as 3 eng told me ..
WIll update you on the status ..
my wires are just like the one on the previous web page that i send ..
Ryan
foleyr .. ..........
“Wise men talk because they have something to say, Fools talk because they have to say something”
|
DaveR
GenII
9/13/2002
16:45:52
| RE: IAT Adjuster
IP: Logged
Message:
Yeah, that's what I ended up with. I originally figured it would have been one black/white pair and a second black/white pair. Whatever. It works
|
foleyr
GenIII
9/13/2002
22:24:57
|  RE: IAT Adjuster
IP: Logged
Message:
Got it working .. just make sure that the 2 black wires are going to the PCM and the 2 white wires are going to the sensor .. god damm .. where did all of this power come from .. jsut by tricking a sensor ..
Nice ..
Need to find me a r/t to beat now ... .
Ryan
foleyr .. ..........
“Wise men talk because they have something to say, Fools talk because they have to say something”
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
