| From | Message |
tazzy
GenIII
 
9/14/2003
23:15:49
|
 Subject: MSD???
IP: Logged
Message:
What all will I need to put an MSD6 on my dak??
Wire harness.Extras...tach adapter??
also..which coil would be the best?
Thanks in advance..
Brass Cap& Rotor
K&N Drop in
Relocated IAT
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
J and J Auto
GenII
9/15/2003
05:49:14
|  RE: MSD???
IP: Logged
Message:
You can get the adapter plugs from MSD if you use
your stock coil.
All you need to use is the 2 existing coil wires,
1 signal - and on off +
12 volt and ground.
Easy to install
MSD SS Blaster but if you use a hot coil get some
good wires the stock wires wont last long they
like to burn off near the connectors especially
the coil wire.
Stock coil plug gap + .005 regular plug
MSD start out at .050 and see what the plugs look
like if running hot (white) open the gap you can
play with the gap untill your plugs are a nice
tan color (as MSD recomends)
On my AP3923 platnium tip I am running .060
and nice tan color
Larry
J&J Auto
|
tazzy
GenIII
9/15/2003
08:39:36
| RE: MSD???
IP: Logged
Message:
Thanks Larry..
How much improvement will i notice??
Brass Cap& Rotor
K&N Drop in
Relocated IAT
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
tazzy
GenIII
9/15/2003
12:29:43
| RE: MSD???
IP: Logged
Message:
Just put in MSD6a.ignition..waiting on coil..
was easy..lol
Brass Cap& Rotor
K&N Drop in
Relocated IAT
MSD6a
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
J and J Auto
GenII
9/15/2003
16:44:00
| RE: MSD???
IP: Logged
Message:
You will notice a stronger low end,
What plugs are you running you will need to open
them up or they will run hot with the setup.
I would start at .050 run it a hundred miles or
so and see what they look like. on reg plugs
If you run the AP with the platinum tip you can
run between .055 .060 bigger flame front that is
what I am doing and it runs great
I tried the reg 3923 at .055 .060 and it runs way
to hot so I put the AP back in, it makes a
noticeable differance.
.045 .050 is max on a reg plug with MSD
Larry
J&J Auto
|
tazzy
GenIII
9/15/2003
18:28:35
| RE: MSD???
IP: Logged
Message:
Just got the coil.p/n 8228..but the plugs are different..
any sugestions....
Brass Cap& Rotor
K&N Drop in
Relocated IAT
MSD6a
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
J and J Auto
GenII
9/16/2003
09:22:33
| RE: MSD???
IP: Logged
Message:
Call MSD they have adapter plugs for most set ups
Or make your own. Check out radio shack some stores carry plugs
Larry
J&J Auto
|
tazzy
GenIII
9/17/2003
18:53:49
| RE: MSD???
IP: Logged
Message:
got the coil installed.Radio shack 2 pins,pigtailed them..epoxied the pins into the coil..put quick plugs on the pigtail ends..
was getting a coil code..installed the 8910 tach adapter no codes now...
Now if I can get more off the line power I'll be happy...
Brass Cap& Rotor
K&N Drop in
Relocated IAT
MSD6a
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
