| From | Message |
markmith
Dodge Dakota
JOIN HERE
10/26/2006
15:12:21
|
 Subject: OBD1?
IP: Logged
Message:
My truck is throwing the code 22 after I turn the switch on and off 3 times. I think it has something to do with the volts running to the temp sensor. I have replaced both the temp sensors that it is talking about and I am still getting the code, I am confused?!? Yes I did reset the computer. What to do next? Maybe short in wires possibly? Any help would be appriciated. By the way the temp sensors I replaced where right by the thermostat housing, one to the right and one to the left. Will it affect my performance any? Also I am getting one about the Emissions Maintence reminder light? What the heck is that? Will it affect my performance to?
92 dak. w/ a 3.9, 5 spd, 2 whl dr.
|
zzark
*GenII*
10/26/2006
17:09:25
|  RE: OBD1?
IP: Logged
Message:
You are correct for code 22. Go here to read a good explanation and troubleshooting
http://dodgeram.org/tech/gas/Trouble/Fault-22.htm
What is the other code you get for Emissions Maintence reminder light?
Code List
http://dodgeram.org/tech/gas/Trouble/pcm_fault_code.htm
zzark
|
markmith
Dodge Dakota
JOIN HERE
10/26/2006
19:31:03
| RE: OBD1?
IP: Logged
Message:
62* PCM failure SRI miles not stored: Unsuccessful attempt to update Service Reminder Indicator miles in the PCM EEPROM (memory).
What the heck is that? That is the code it is sending... Hmm? Scratch, scratch...
|
?
Dodge Dakota
JOIN HERE
10/26/2006
22:39:30
| RE: OBD1?
IP: Logged
Message:
Check ground connections , in particular
one connects to back of alternator bracket.
Computer ground..
I was not aware of that year truck having , but
possible - sensor on or near centre of rear
axle may be faulty re code 62.
|
markmith
Dodge Dakota
JOIN HERE
10/28/2006
01:31:06
| RE: OBD1?
IP: Logged
Message:
What? Code 62? 92 dak. 3.9 w/ 5 spd man.
|
zzark
*GenII*
10/28/2006
09:03:34
| RE: OBD1?
IP: Logged
Message:
Have you reset the computer/PCM?
If not, do it.
Remove neg battery cable.
Leave it off for 20 minutes.
Turn Ignition Key to start, and hold for 30 seconds.
That will drain all the electricity from the pcm, and reset it.
Install cable.
Start truck and let it idle for 2 minutes. Do not give it any gas for the 2 minutes. PCM needs to relearn idle.
Check for codes.
zzark
|
markmith
Dodge Dakota
JOIN HERE
10/28/2006
16:12:37
|  RE: OBD1?
IP: Logged
Message:
I have reset the computer... I am still getting the same code? I don't know exactly what it means. The code is 62. Thanks again for the responses.
|
markmith
Dodge Dakota
JOIN HERE
10/28/2006
20:46:54
|  RE: OBD1?
IP: Logged
Message:
I am still wondering what the code means? Any help would be appriciated.
|
Dan M
Dodge Dakota
JOIN HERE
10/30/2006
09:49:54
| RE: OBD1?
IP: Logged
Message:
Code 62 is PCM failure.
62 EMR mileage cannot be stored in EEPROM
62 PCM failure SRI mile not stored
http://www.allpar.com/fix/80s-codes.html
allpar. all things MOPAR!
- Dan M
|
markmith
Dodge Dakota
JOIN HERE
10/30/2006
10:32:28
| RE: OBD1?
IP: Logged
Message:
Does that mean I need a new PCM? PCM, is that the computer? Is it expensive and where should I pick one up?
Thanks,
Markmith
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
