| From | Message |
graham
Dodge Dakota
JOIN HERE
4/17/2004
19:27:21
|
 Subject: 33's
IP: Logged
Message:
will 33's fit with two inch blocks and cranking the bars without trimming its a 97 4x4
|
Dakota dude
Dodge Dakota
JOIN HERE
4/19/2004
10:26:01
|  RE: 33's
IP: Logged
Message:
Yea probably, but it still may scrub the frame. I going to put 33 inch bridgestone dueler MT's on mine with no lift at all.
|
JOKER
Dodge Dakota
JOIN HERE
4/19/2004
12:57:53
| RE: 33's
IP: Logged
Message:
yes it fits i did it. i have a 98 4x4 318 club cab and all i added was a 2" lift kit and 33x10.5 bfgoodrige and it looks great and dosent robe.your right you have to crank the torshen bars but not enouth for you to f*ck up you new tires. i would like it for you to contact me so we could exchange our truck picturs
I m alsow on (cardomain). to find me you need to go in dodge dakota off road and look for JOKER
|
THRASHER
Dodge Dakota
JOIN HERE
4/19/2004
14:16:22
| RE: 33's
IP: Logged
Message:
I am running 33x12.5 swampers with no rubbing with only a 2in blocl/t-bars cranked. The lucks slighty touch the frame at full lock. but it almost isnt noticable..
|
graham
Dodge Dakota
JOIN HERE
4/19/2004
18:31:40
| RE: 33's
IP: Logged
Message:
joker i have no pics.yet because i haven't put any of my stuff back on the truck yet.idid buy bfgs.i have cranked the bars and am waiting for my blocks to come from crappy tire then i'm going to have an alinement done.then Iwill put my tires on i also have a chrome roll bar with five kc's and two backups the truck only has 57000kms mostly do to sitting all last winter.
|
JOKER
Dodge Dakota
JOIN HERE
4/21/2004
12:52:25
| RE: 33's
IP: Logged
Message:
HI GRAHAM MY ADVICE IS NOT TO INSTALE THE LIFT KIT EXACTLY LIKE THEY SAY IN THE KIT OR ELSE YOU WILL HAVE A BIG GAP ON TOP OF YOUR RADIATOR. TO KEEP IT LOOKING ORIGINAL I CUT THE FAN SHROUD IN 2. ON EACH SIDE LOW ENOUGH SOW YOU DONT SEE IT AND TOOK RUBER AND BOLTED IT TO THE SHROUD TO FILL THE HOLE. IT TAKES A LITTLE LONGER BUT THE END RESOULT IS GREAT.
YOU HAVE A 97 4X4 THAT MEANS THET YOUR 4X4 SHIFTER IS ON THE FLOOR. IN THE KIT THEY GIVE YOU JUST A LITTLE PIECE OF ROD THAT YOUR SUPOSED TO LENGTHEN YOUR SHIFTER WHIT
BUT IF YOUR LIKE ME AND DONT FELL LIKE TAKING THE ENTIRE ROD OFF,MARKING IT, THEN CUT IT.THEN WELDING IT. YOU COULD DO LIKE ALOT OF US AND JUST TAKE OFF THE TOP OF THE SHIFTHER AND USE BOLTS AND NUTS TO GET THE SHIFTHER HIGHER.
DONT DO THE SAME MISTAKE AS ME. DONT FORGERT ABOUT YOUR SPARE TIRE. THE BAR THAT CONNECTS FROM THE BACK OF THE BUMPER TO THE SPARE YOU NEED TO TAKE IT OFF BEFORE YOU START LIFTING THE BOX OR IT WILL BEND. GOOD LUCK KEEP ME INFORMED
ps. if you know how i could seend you some pictures. it would be cool if you could tell me
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
