| From | Message |
pbxr
GenIII
12/16/2002
06:09:32
|
 Subject: Another Taylor Wire ?
IP: Logged
Message:
When you guys, (almost all here), upgraded your sparkplug wires to Taylor, MSD, Accell, etc, did you notice a hesitation or stumble if you will at idle? ALso do you have to reset the pcm when changing the wires? I have checked to make sure of proper contact on sparkplugs, and the wire seem good(type wher you install ends), and it runs like a t top at regular speeds. I did notice that my idle rpm is around 700, form around 900 before the swap. THanks for info
'01 Sport Auto 3.9, CC, 3923s, Intense Cold Intake, Dynomax SuperTurbo 17748, Wal-Mart special roll on bedliner, MOOG upper and lower ball joints
|
Simpleman96
Dodge Dakota
JOIN HERE
12/16/2002
11:31:28
| RE: Another Taylor Wire ?
IP: Logged
Message:
I do have a stumbling prob at idle with taylor wires on it, but do not know if the wires are what is causing it. I have sometimes thought about changing back to smaller wires to see if it helps but have not as of yet. You should not have to reset the computer when installing new wires but it couldn,t hurt.
|
Nitro Junkie
R/T
12/16/2002
13:11:02
|  RE: Another Taylor Wire ?
IP: Logged
Message:
i have talyors and i dont have any of the above problems ?
2000 R/T
Belltech 2"-3" Drop w/ Nitro Drop Shocks
40 Series Flowmaster Dumped Exhaust
8mm Taylor Spiro Pro wires w/ Autolite 3923's
Mopar Performance Distributor, 180 T-Stat
Turbo City Dual Tube Air Intake w/ Twin 5" Round K&N Filters
Speed Scene Grill (Upper&Lower)
|
Simplleman96
Dodge Dakota
JOIN HERE
12/16/2002
17:31:18
| RE: Another Taylor Wire ?
IP: Logged
Message:
Mine could be attributed to a weak coil as well or many things, i am just tired of puting money into this POS.
|
Neil
Dodge Dakota
JOIN HERE
12/17/2002
06:21:30
| RE: Another Taylor Wire ?
IP: Logged
Message:
If you have checked that they are all making good connections and still have a stumble, have you made sure that the correct wires are going to the correct plugs.
|
pbxr
GenIII
12/17/2002
06:41:44
| RE: Another Taylor Wire ?
IP: Logged
Message:
I am almost 99.9% positive its in the wires I made. I will try to isolate tonight with stocker wires one@ a time. I did replace on wire at a time
when I intalled the new wires, so somewhere I am not making good contact. Thank for the help...
'01 Sport Auto 3.9, CC, 3923s, Intense Cold Intake, Dynomax SuperTurbo 17748, Wal-Mart special roll on bedliner, MOOG upper and lower ball joints
|
ticats
Dodge Dakota
JOIN HERE
12/17/2002
06:50:11
| RE: Another Taylor Wire ?
IP: Logged
Message:
Are these Taylor wires a universal set or a custom set for the magnum engines? TIA.
ticats
|
pbxr
GenIII
12/17/2002
11:01:58
| RE: Another Taylor Wire ?
IP: Logged
Message:
In this case, I bought a universal set, for like 30 bucks @ truckperformance.com.
'01 Sport Auto 3.9, CC, 3923s, Intense Cold Intake, Dynomax SuperTurbo 17748, Wal-Mart special roll on bedliner, MOOG upper and lower ball joints
|
custman
Dodge Dakota
JOIN HERE
12/17/2002
14:55:52
| RE: Another Taylor Wire ?
IP: Logged
Message:
I had a stumble problem with 8mm Taylors on my T/A. I changed them out to Summit universal 90deg boots and have not had the stumble return. I was told if you run the resistor core Taylor wires (like I did)you can get a stumble, the spiral core don't have this problem on a friends Camaro.
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
